S71 “Custom Nitro S” Vintage ’66 3-Tone Sunburst Super Heavy Relic, Handwound Pickups. Made in USA.

Home/CUSTOM RELIC/S71 “Custom Nitro S” Vintage ’66 3-Tone Sunburst Super Heavy Relic, Handwound Pickups. Made in USA.

S71 “Custom Nitro S” Vintage ’66 3-Tone Sunburst Super Heavy Relic, Handwound Pickups. Made in USA.

1590,00CHF

Out of stock

S71 Custom made unique « Nitro S Vintage 66 3-Tone Sunburst Super Heavy Relic ». selected lightweight body (3,3kgs/6.6lbs for the whole guitar) Custom made by USACG in Washington.
Reversed headstock accurate “1966 Oval C” Neck specs « ROASTED Flame/Quartersawn maple « AAA Dark Rosewood fretboard with Compound Radius 9.5-14, Engraved Logo, Custom made by luthier near New-York with Nitrocellulose finish.
Handwound « California Glass 66 » Pickups  in, Dallas Texas. « 7-Sounds «  wiring mod. Gotoh Japan Tremolo, Genuine Fender tuners & Gotoh neckplate with serial number. C.O.A included.
Custom made in USA.
NEW guitar, including C.O.A and invoice.
(the hardcase in pictures is for illustration purposes only)
S71 Custom Guitars is a professional seller commercially registered in Switzerland.

Out of stock

Category:

Description

66’s Neck « Oval C »Luthier custom made in USA, specs:
  • Roasted Flame/Quartersawn maple neck
  • AAA Dark Rosewood fretboard
  • .840 @ 1st fret / .960 @ 12th fret
  • Compound Radius 9.5 to 14
  • “Cream Clay” Vintage style front and side dots
  • 22 Tall/Medium frets from Jescar USA
  • Headstock Trussrod
  • Graphtech « Nubone » nut, made in Canada
————
Genuine custom hand wound vintage pickup full specs:

  • Model T-166 genuine Collins custom hand wound 5/2 Hybrid pickup set with some modern touches  
  • California Glass is a .187 Alnico 5, Alnico 2 hybrid set of single coil pickups with vintage stagger. Magnets oriented S-N-S spec and calibrated for strength
    These pickups are overwound 5% at the bridge and 5% underwound at the neck with the middle pickup wound to late ’60’s specs. The underwinding of the neck will give a small mid scooping, while the overwinding at the bridge will provide a mid boost. The Alnico 5 magnets in the 6th, 5th and 4th string positions will keep the bottom end tight and focused while the Alnico 2 magnets in the 3rd, 2nd and 1st string positions will round out the top and coax out the bell tones.
    High quality vulcanized fiber flatwork red .062 top with gray .093  bottoms
  • Though ohms are subject to change in temperature these read around
  • 5.39 K (neck) 2.13 Henries
  • 5.72 K (mid) 2.41 Henries
  • 5.95 K (bridge) 2.55 Henries
    measured around 70 degrees

    The sandcast alnico 5 and 2 magnets were sealed before winding in my own resin formula to prevent magnet to wire failure
    Wound with a beautiful bright red modern poly-nylon AWG42 wire and potted in paraffin/bees wax to silence microphonics.

    Vintage black/white cloth wiring about 12″ long for the most demanding hookups. Vintage surgical rubber tubing with nickel screws

  • 52mm spacing profile

    Note: These Model T-166 scatterwound pickups will hum cancel in the 4th and 2nd positions

  • They have all the quack and bell tones early single coils are known for
    Dripping with tone and ready to rock

    They are at home in the California Surf and Sun but are equally home in a Nashville Studio or a Classic Rock venue

Go to Top